clean a hayward salt cell

We use a Hayward Aquarite salt cell. When i test my water for salt with test strips i get a reading of 3700.

How To Clean Your Hayward Salt Chlorinator Turbo Cell Hayward Poolside Blog Pool Supplies Spa Pool Cell

In this Pool Care Basics video we explain how to clean a salt chlorine generator cell.

. On some units simply press the button next to filter on the control panel. Coil the wiring harness alongside the cell before you go for soaking. If no deposits are visible reinstall the cell. Turn off the power to the system and deactivate the pool pump before removing the Turbo Cell.

Once removed look through the cell and inspect for scale formation light colored crusty or flaky deposits on the plates and for debris that is caught on the plates. Ideally this should be done at the circuit breaker. Immerse the cell to the top of the wiring. Pour undiluted distilled white vinegar into the cell and leave it to soak there overnight.

Simply thread the cell cleaning stand onto your turbo cell. How To Clean a Hayward AquaRite Turbo Cell 1. The solution can remove all sorts of remaining debris within a fortnight. Discard the acid and water inside the cell.

Directions Pour 8 cups of water in a bucket and then add 1 cup of muriatic acid. So i have a hayward swim pure plus T-3 swg and the problem im having is that im now having to clean my cell almost every 5 days. Follow the steps for a guide through the process. Remove the Turbo Cell.

Screw the salt cell from the cord end into the cleaning stand. Your first step in cleaning the Hayward AquaRite Turbo Cell is to turn off the power to the pump and Chlorine Salt. The safe mixing of acid and water to a 1 to 4 ratio and the cleaning of the unit with the acid after a pre rinse with the hose for 10 minutes. Let it sit for 10-15 minutes to allow the foaming action to happen.

STEP 2 Suit up with protective gear including cover-alls gloves and goggles. Switch off the salt cell and disconnect completely from the socket. This will result in cleaner cells directly. STEP 1 Switch of the system and remove the salt cell.

Soak the saltwater cell or hot tubs as the case may be in a container with vinegar solution for a night. Turn off the power to the system and deactivate the pool pump before removing the Turbo Cell. Place the cell into the stand with the cord section on the bottom which ensures that its thoroughly cleaned. The steps below are how a Pentaur salt cell can be cleaned with vinegar.

Pour the solution into the cell. STEP 3 Add muriatic acid to water in the ratio of 1 part acid for every 5 parts of water. This is followed by post rinse. Next fill the device with the chemical solution till full.

How to Clean Your Hayward Salt Chlorinator Turbo Cell. After cleaning my cell and installing it my swg reads 3700-3800 but after 4-5 days the salt level drops to under 2700 and thus stops generating clorine. Pour the mixture into the bucket or otherwise dispose of it safely. Remove the Turbo Cell.

Step 2 Next relieve the water pressure in the pool line. Once its done transfer. Use a high-pressure garden hose and rinse it. To extend the lifetime of Hayward T-CELL-15 You must be cleaned at least every 3 months or every 500 hours of operation and clean the cell if necessary.

The cell is only 1 year. For optimum TurboCell operation and life you will need to inspect your cell approximately every 3 months of operation or 500 hours and clean the cell if n. In addition flip the breaker for the control panel or turn off. Then fill the cell with a mixture of 1 part muriatic acid to 4 parts of water.

Once removed look through the cell and inspect for scale formation light colored crusty or. Attach the salt cell to the cell stand. We use a Hayward Aquarite salt cell but the same instructions can be. To clean the the cells should be checked in pH calcium levels in the two bills will have to be in reasonable condition.

Let it soak for about 15 minutes or until the fizzing and bubbling stops. Top Step 1 Your first step in cleaning the Hayward AquaRite Turbo Cell is to turn off the power to the pump and Chlorine Salt Generator. Pour an additional mixture of acid and water into the cell. Allow the cell to soak in the acid and water solution until the acid stops bubbling.

It should cover the blades entirely. Next relieve the water pressure in the pool line. Check your manufacturers instructions on how to do this specifcally for your type of chlorinator. On other units turn it off at the onoff.

In this case since this system does not have a relief valve we.